How to set up my modem router for DS244WTV-V1, V2， v3,C5912TR-V2 ( EWAN with Dynmaic solution)

一、Hardware Connection EWAN with Dynmaic

1、Plug the power adapter included in the package into the socket and plug the other side into the power port of product. And press the ON/OFF switch button to power on the system.
 2、There are two methods to connect your device. You can just choose one method to connect your device according to your actual situation. Wired: Connect your computer to LAN port 1 , 2, 3 or 4 of product using an Ethernet cable.  Wireless: Connect your device to product-V3 using the SSID and key (wireless password) printed on the bottom of the modem router.
 3、Plug the Ethernet cable that has connected to the internet into the WAN port of the router.
 4、Enabling VoIP feature if necessary, connect the FXS port of product to your phone device using telephone line.

二、Basic Configuration In Web UI Page

 1、Launch your web browser, enter 192.168.1.1 on the address bar, and press enter to go to Web User Interface page.

2、Enter the login username and password labeled in the bottom of product-

 3、The Basic Settings > WAN Interface > WAN Services page is displayed. Select your EWAN Dynamic Connection mode editing Settings. Enter MTU or other related information. Then click Apply

Note, Device require reboot or power off&on to take effect after setting change

 

4、How to create a new EWAN with PPPO

1、Set New WAN，Interface:EWAN1,Mode:DHCP,Create.

2、2, 1, Connection Name:EWAN Dynamic2, Enable: enable 3, MTU:1500, 4 IP Protocol Type:IPv4, 5. NAT: Enable 6. Click Apply

 Note, Device require reboot or power off&on to take effect after setting change.

 

FAQ
 Q1: How to restore this modem router to factory settings?
 A1: While the router is powered on, long-press the Reset button about 6
 seconds until the LED light starts blinking.
 Q2: If I can't access the web UI page of the router after entering
 192.168.1.1, what should I do?
 A2: Please try the following methods to log in again.
 Make sure the connection of DSL/WAN and LAN port(s) is correct.
 Make sure you enter the correct IP address (192.168.1.1) to log in.
 Make sure the IP address of your computer is configured as Obtain an IP
 address automatically and Obtain DNS server address automatically.
 Use another web browser to log in again.
 Reset the modem router to factory default settings and try again.
 Q3: If I forget the login password of the modem router, what can I do?
 A3: Please reset the modem router and use the username and password
 (labeled in the bottom of DIA-C5912TR) to login the modem router’s web
 UI page.
 Q4: If I forget my wireless network password, what can I do ?
 A4: Please refer to the following methods.
 If you have not changed the wireless password, it can be found on the
 product label at the bottom of the router.
 Login to the web UI page, go to Basic Setup > Security Setting page
 to reset your wireless password.
 Q5: What can I do if VDSL Modem (when through method 1 in hardware
 connection part) can not synchronize?
 A5: You can determine if the synchronization is successful based on the
 DSL indicator status. (Refer to LED indicators explanation)
 Check that the connection of the VDSL Splitter is correct.
 The correct connection method of VDSL Splitter is: the entry LINE connects
 to the LINE port, VDSL Modem connects to the Modem port, and the
 telephone connects to the PHONE port.
 Call the service provider to check whether the VDSL line is normal.
 Q6: What can I do if I can’t access the internet (when through method
 2 in
 hardware connection part)?
 A6: Please try the following methods.
 Check if the internet is working properly by con